We made this set of tools for your series 1 or later Lambretta scooter, it is the set just like the one found in Lambrettas when they were new from the factory, includes what you see in the photo (i.e. rear jack stand, combo sparkplug/14mm nut wrench, screw driver, combo rear hub/14mm wrench and combo open ended wrench.

Ser.3 Rear Floorboards

To install the rear floorboards and 4 rear plastic rails on Series 3.
Consists of:
10 m5 nuts, 10 m5 spring washers, 4 m5 OD washers, 8 speed clips.

part # H 97 - $8.64 zinc
part # H 97/s - $12.96 stainless

Ser.3 Front Plastic Rails

For installing the outer front 2 plastic rails on Series 3. Consists of:
4 m5 nuts, 4 m5 spring washers, 4 m5 OD washers, 2 speed clips (not shown)

part # H 197 - $3.78 zinc
part # H 197/s $5.67 stainless

Ser.3 Front Endcaps

Hardware that goes through the endcaps consisting of:
6 m4 x 20 screws, 2 m4x10 screws, 6 m4 x 7 nuts, 6 m4 spring washers, 6 m4 OD washers, 2 "T" nuts, 2 m6 spring washers

part # H 301 - $9.06 zinc
part # H 301/s - $12.70 stainless

Ser.3 Front Rails

For installing the 4 front alloy channels on Series 3 and DL consists of:
6 m5 x 10 screws, 2 m5 x 16 screws, 8 m5 spring washers, 2 OD flat washers, 8 m5 nuts

part # H 298 - $7.02 zinc
part # H 298/s - $10.53 stainless

Ser 3 Horncover Grill

This kit consists of:
2 m4 x 10 screws

part # H 304 - $.54 zinc
part # H 304/s - $.81 stainless

Ser.3 Fan and Cylinder Shrouds

To install both the cylinder and flywheel/fan shroud on Series 3. Consists of:
7 m5 x 10 hex bolts, 7 m5 lock washers, 1 m8 x 14 hex bolt, 1 m8 wave washer

part # H 315 - $4.32 zinc
part # H 315/s - $6.48 stainless

Bench or Single Seat Series 1,2,3

One set is good for either front or rear single seat or for front Pivot section of bench seat consisting of:
4 m8 x 25 bolts, 4 m8 nuts, 4 m8 spring washers

part # H 342 - $4.32 zinc
part # H 342/s - $6.48 stainless

Ser 3 rear seat or dual latch post

4 x 8m plastic washers

part # H 347 - $1.08

Ser.3 Headset

Hardware kit for securing the headset top consisting of:
2 m5 x 40 screws, 2 m5 countersunk internal lock washers

part # H 14 - $1.08 zinc
part # H 14/s - $1.62 stainless

Ser.3 TV-SX-Special Headlight Rim

Kit for securing the headlight rim consists of:
4 m3 x 20 screws

part # H 57 - $1.08 zinc
part # H 57/s - $1.62 stainless

Ser.3 Li Headlight Rim

Kit for installing the headlight rim on your Series 3 Li consisting of:
3 m4 x 10 screws, 3 m4 finishing washers

part # H 55 - $1.62 zinc
part # H 55/s - $2.43 stainless

Ser 3 Light Switch

Kit for securing the light switch to handlebar consists of:
2 m3 x 22 screws

part # H 65 - $.54 zinc
part # H 65/s - $.81 stainless

Ser.1-2-3 Wheel Rim

This kit is for 10" wheels consisting of:
4 x B95 (acorn nut with nylock), 4 x B96 (open nylock nut)

$15.00 per wheel

Ser 3 Horncast

This kit includes: 2 m5 x 10 panhead screws for the top, 2 m6 x 18 allen screws for the horncast badge clip, 2 m6 serrated washers for allens, 2 m5 x 20 oval head screws for the lower horcast, 2 m5 finishing washers for screws, 2 m5 x 16 hex bolts for the horncast bottom, 2 m5 wave washers for bolts

part # H 162 - $3.78 zinc
part # H 162/s - $5.60 stainless

Ser 3 Front Fender

This kit includes: 2 m5 x 25 screws for the bottom (under aluminum channel), 2 m5 nuts for above screws, 2 m5 wave washers for above nuts, 2 m5 x 20 oval screw for the top, 2 m5 nuts for the above screws, 2 m5 wave washers for above screws, 2 m5 finishing washers

part # H 411 - $3.78 zinc
part # H 411/s - $5.60 stainless

Ser 3 Bridgepiece

This kit includes:
2 m5 x 25 screws, 2 m5 nuts, 2 m5 wave washers

part # H 71 - $1.62 zinc
part # H 71/s - $2.43 stainless

Ser 1 & 2 Rear Floorboards/floor rails

This kit includes:
8 m5 nuts, 8 m5 spring washers, 8 m5 flat washers, 12 speed clips (no stainless)

part # H 81 - $9.72 zinc
part # H 81/s - $14.58 stainless